401DB/801DB AMPLIFIER OWNER’S MANUAL (MODE D’EMPLOI)877 COUSTIC COUSTIC.COM
COUSTIC.COM19BIENVENU. . . Chez COUSTIC, un univers de puissance et de clarté. Les nouveaux amplis classe D 401DBet 801DB délivrent la puissance la pl
PANNEAU DES SORTIESFigure 2 : Panneau des sorties et des connecteurs9. INDICATEUR DE MISE EN TENSION ET DE PROTECTIONLed verte : l’amplificateur est a
COUSTIC.COM23INSTALLATIONEn achetant le 401DB/801DB, vous avez déjà fait un grand pas vers un son pur et naturel. Avantde passer à l’installation et p
COUSTIC.COM25 Figure 7 : Système multi amplifié Figure 6 : Installation traditionnelleBI-AMPLIFICATIONUn système bi-amplifié est généralement constitu
COUSTIC.COM27INSTALLATIONCONNEXION DU SIGNALConnectez l’entrée RCA (input) de l’ampli à la sortie RCA de votre source. Un câble vendu séparé-ment est
COUSTIC.COM29RÉGLAGESSÉLECTION DE LA FRÉQUENCE DE COUPURELe filtre actif passe bas est réglable en continu de 20Hz à 200Hz. Cela permet tous les régla
COUSTIC.COM31EN CAS DE DIFFICULTÉSymptôme Cause probable1. Ne s’allume pas Vérifier les connexions à l’ampli alimentation masse et remote. Vérifier la
COUSTIC.COM33CARACTÉRISTIQUES TECHNIQUES401DB 801DBPuissance sous 14,4volts 1 x 200 Watts 1 x 400 W4 ohms, 2% THDPuissance sous 14,4volts 1 x 400 Wat
COUSTIC.COM35NOTES:COUSTIC LIMITED WARRANTYIMPORTANT NOTICE TO CONSUMER:Coustic offers the following warranty to the ORIGINAL PURCHASER of COUSTIC pro
COU000770 Rev A 2/02 NDM183©2002. COUSTIC IS A REGISTERED TRADEMARK OF MITEK CORPORATION. ALL RIGHTS RESERVED.7676 SOUTH 46 STREET, SUITE 2020, PHOENI
WELCOME . . . to the Coustic world of power and clarity. The new 401DB/801DB class D mono-block ampli-fiers deliver the highest quality low frequency
CONTROLS, INDICATORS, AND TERMINALSINPUT PANELFigure 1: Input Panel Terminals and Controls1. SUBSONIC FILTER SELECT SWITCH The subsonic filter switch
COUSTIC.COM7INSTALLATIONBy purchasing the 401DB/801DB power amplifiers, you are already one step closer to experienc-ing the purest and most natural s
COUSTIC.COM9 Figure 7. Typical Multi-amplifier System Figure 6. Typical System connectionBI-AMPLIFICATIONA bi-amplified system normally consists of an
COUSTIC.COM11INSTALLATION continuedINPUT CONNECTIONSConnect the RCA input jacks of the amplifier to the output of the source unit (i.e., radio, casset
COUSTIC.COM13ADJUSTMENTSCROSSOVER FREQUENCY SELECTIONThe low-pass continuously adjustable crossover frequencies are selectable between 40Hz and200Hz.
COUSTIC.COM15TROUBLE SHOOTING SECTIONSYMPTOM PROBABLE CAUSE1. No power Check connections to the amplifier's Ground, B+ and Remoteterminals. Check
COUSTIC.COM17SPECIFICATIONS:401DB 801DBRated Power @ 14.4 V (2% THD): 1 x 200 Watts 1 x 400 Watts4 Ohm Rated Power @ 14.4 V (2% THD): 1 x 400 Watts 1
Comments to this Manuals